Ürün Açıklaması
Tek kafalı sistem
General specifications
Sensing range30 … 500 mm
Adjustment range50 … 500 mm
Dead band0 … 30 mm
Standard target plate100 mm x 100 mm
Transducer frequencyapprox. 300 kHz
Response delayminimum : 20 ms
factory setting: 40 ms
Sensor cycle time≥ 10 ms (factory setting) ;
programmable to 60 s
Temperature influencewith temperature compensation: ≤ ± 0.75% of the end value 10 min after switching on the sensor (factory setting)
with enhanced temperature compensation: ≤ ± 0.75% of the end value 2 min after switching on the sensor
without temperature compensation: 0.17 %/K
Memory
Non-volatile memoryEEPROM
Write cycles300000
Indicators/operating means
LED greensolid: power on
flashing: standby mode or IO-Link communication
LED yellowsolid: object in evaluation range
flashing: switch point programming, object detected
LED redsolid: error
flashing: switch point programming, object not detected
Electrical specifications
Operating voltage10 … 30 V DC , ripple 10 %SS
No-load supply current≤ 50 mA
Power consumption≤ 700 mW
Time delay before availability≤ 300 ms
Interface 1
Interface typeIO-Link (via C/Q = Pin 4)
IO-Link revision1.1
Device profileSmart Sensor Profile 2
Process data width32 bit
Device ID0x300601 (3147265)
Transfer rateCOM2 (38.4 kBit/s)
Min. cycle time3 ms
SIO mode supportyes
Compatible master port typeClass A
Class B (use 3-pole adapter or 3-wire cable)
Interface 2
Interface typeIrDA (infrared interface)
Modepoint-to-point connection
Transfer rate115.2 kBit/s
Maximum communication distance5 cm
Input/Output
Input/output type1 synchronization connection, bidirectional
0 Level0 … 1 V
1 Level2.5 V … UB
Input impedance> 22 kΩ
Output rated operating currentcurrent source < 2.5 mA
Pulse length≥ 1 ms with external control, low active
Synchronization frequency
Common mode operation≤ 100 Hz
Multiplex operation≤ 71 Hz / n , n = number of sensors , n ≤ 10Switching outputOutput type2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected
Rated operating current100 mA , short-circuit/overload protected
Switching frequencyfactory setting: 14 Hz
programmable to 33 Hz
Voltage drop≤ 2.5 V
Repeat accuracy≤ ± 0.1 % of full-scale value
Range hysteresis1 % of the adjusted operating range (default settings), programmable , min. 1 mm
Off-state current≤ 100 µACompliance with standards and directivesStandard conformity
StandardsEN IEC 60947-5-2:2020
IEC 60947-5-2:2019
IEC 61131-9:2013Approvals and certificatesUL approvalcULus Listed, Class 2 Power Source
CCC approvalCCC approval / marking not required for products rated ≤36 VAmbient conditionsAmbient temperature-25 ... 70 °C (-13 ... 158 °F)
Storage temperature-40 ... 85 °C (-40 ... 185 °F)Mechanical specificationsConnection typeConnector plug M12 x 1 , 5-pin
Housing diameter18 mm
Degree of protectionIP67
Material
Housingstainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic parts
Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam
Installation positionany position
Mass45 g
Tightening torque, fastening screwsmax. 30 Nm
Factory settings
Output 1near switch point: 50 mm
far switch point: 500 mm
output function: Window mode
output behavior: NO contact
Output 2near switch point: 50 mm
far switch point: 250 mm
output function: Window mode
output behavior: NO contact
Beam widthwide
